Индуктивный датчик Inductive sensor NCB10-30GM40-N0-50M Pepperl+Fuchs

Описание товара

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		10 mm
Installation		flush
Assured operating distance		0 ... 8.1 mm
Actual operating distance		9 ... 11 mm typ.
Reduction factor rAl		0.35
Reduction factor rCu		0.3
Reduction factor r304		0.75
Nominal ratings
Nominal voltage		8 V
Switching frequency		0 ... 200 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 2.2 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTFd		1870 a
Mission Time (TM)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		cable PVC , 50 m
Core cross-section		0.75 mm2
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67
Cable
	Bending radius	> 10 x cable diameter
Equipment protection level Dc (tc)
Instruction		Manual electrical apparatus for hazardous areas
Device category 3D		for use in hazardous areas with combustible dust
Certificate of Compliance		PF 15CERT3774 X
CE marking		[*PD-Z02585A*]
ATEX marking		II 3D Ex tc IIIC T80°C Dc The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013, EN 60079-31:2014 Protection by enclosure tc Some of the information in this instruction manual is more specific than the information provided in the datasheet.
General		The corresponding datasheets, declarations of conformity, EC-type examination certificates, certifications, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents can be found at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet.
Installation, commissioning		Laws and/or regulations and standards governing the use or intended usage goal must be observed. If the Ex-relevant identification is printed exclusively on the adhesive label provided, this label must be affixed in the immediate vicinity of the sensor! The background surface to which the adhesivelabel is to be applied must be clean and free from grease! The applied label must be durable and remain legible, with due consideration of the possibility of chemical corrosion!
Maintenance		No changes can be made to apparatus, which are operated in hazardous areas. Repairs to these apparatus are not possible.
Special conditions
	Minimum series resistance RV	A minimum series resistance RV is to be provided between the power supply voltage and the proximity switch in accordance with the following list. This can also be assured by using a switch amplifier.
	Maximum operating voltage UBmax	The maximum permissible operating voltage UBmax must be restricted to the values given in the following list. Tolerances are not permitted.
	Maximum permissible ambient temperature TUmax	Values can be obtained from the following list, depending on the max. operating voltage Ub max and the minimum series resistance Rv.
	at UBmax=9 V, RV=562 &Omega	66 °C (150.8 °F)
	using an amplifier in accordance with EN&nbsp60947-5-6	66 °C (150.8 °F)
	Protection from mechanical danger	The sensor must not be exposed to ANY FORM of mechanical danger.
	Protection from UV light	The sensor and the connection cable must be protected from damaging UV-radiation. This can be achieved when the sensor is used in internal areas.
	Protection of the connection cable	The connection cable must be prevented from being subjected to tension and torsional loading.
	Electrostatic charge	Electrostatic charges must be avoided on the mechanical housing components. Dangerous electrostatic charges on the mechanical housing components can be avoided by incorporating these in the equipotential bonding. Avoid electrostatic charges that can cause electrostatic discharge when installing or operating the device. Information on electrostatic hazards can be found in the technical specification IEC/TS&nbsp60079-32-1. Do not attach the nameplate provided in areas where electrostatic charge can build up.
General information
Use in the hazardous area		see instruction manuals
	Category	1G 2G 3G 1D 3D

Характеристики

Важная информация

Все информационные материалы, представленные на сайте, носят справочный характер и не могут в полной мере передавать достоверную информацию о свойствах и характеристиках товара.

Фотография на сайте служит дополнительным источником для определения совместимости запчастей с Вашим оборудованием, и не может являться основным. Основной источник по совместимости запчастей - актуальная документация производителя оборудования, из которой значимой информацией для заказа являются: название запчасти и каталожный номер.

Запасные части и комплектующие подбираются самостоятельно покупателем строго по каталожным номерам из официальных деталировок производителей. В случае, если номенклатура товара совпадает с фактически поставленной, но не подходит на оборудование - в ее замене или возврате может быть отказано.

Цены на сайте имеют информационный характер и могут отличаться от цен в коммерческом предложении.