Индуктивный датчик Inductive sensor NCB2-12GM40-Z0-V1-3G-3D Pepperl+Fuchs

Описание товара

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Actual operating distance		1.8 ... 2.2 mm typ.
Reduction factor rAl		0.28
Reduction factor rCu		0.23
Reduction factor r304		0.7
Nominal ratings
Operating voltage		5 ... 60 V DC
Switching frequency		0 ... 800 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		2 ... 100 mA
Lowest operating current		2 mA
Off-state current		0 ... 0.5 mA typ.
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTFd		2090 a
Mission Time (TM)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
Equipment protection level Gc (nA)
Certificate of Compliance		PF 15CERT3754 X
Special conditions
	Protection against transients	Ensure transient protection is provided and that the maximum value of the transient protection (140% of 85 V) is not exceeded.
Equipment protection level Dc (tc)
Instruction		Manual electrical apparatus for hazardous areas
Device category 3D		for use in hazardous areas with combustible dust
Certificate of Compliance		PF 15CERT3774 X
CE marking		[*PD-Z02586A*]
ATEX marking		II 3D Ex tc IIIC T80°C Dc The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013, EN 60079-31:2014 Protection by enclosure tc Some of the information in this instruction manual is more specific than the information provided in the datasheet.
General		The corresponding datasheets, declarations of conformity, EC-type examination certificates, certifications, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents can be found at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet.
Installation, commissioning		Laws and/or regulations and standards governing the use or intended usage goal must be observed. If the Ex-relevant identification is printed exclusively on the adhesive label provided, this label must be affixed in the immediate vicinity of the sensor! The background surface to which the adhesivelabel is to be applied must be clean and free from grease! The applied label must be durable and remain legible, with due consideration of the possibility of chemical corrosion!
Maintenance		No changes can be made to apparatus, which are operated in hazardous areas. Repairs to these apparatus are not possible.
Special conditions
	Maximum operating current IL	The maximum permissible load current must be restricted to the values given in the following list. High load currents and load short-circuits are not permitted.
	Maximum operating voltage UBmax	The maximum permissible operating voltage UBmax must be restricted to the values given in the following list. Tolerances are not permitted.
	Maximum permissible ambient temperature TUmax	dependant of the load current IL and the max. operating voltage UBmax Information can be taken from the following list.
	at UBmax=60 V, IL=100 mA	48 °C (118.4 °F)
	at UBmax=60 V, IL=50 mA	56 °C (132.8 °F)
	at UBmax=60 V, IL=25 mA	60 °C (140 °F)
	Protection from mechanical danger	The sensor must not be exposed to ANY FORM of mechanical danger.
	Protection from UV light	The sensor and the connection cable must be protected from damaging UV-radiation. This can be achieved when the sensor is used in internal areas.
	Electrostatic charge	Electrostatic charges must be avoided on the mechanical housing components. Dangerous electrostatic charges on the mechanical housing components can be avoided by incorporating these in the equipotential bonding. Do not attach the nameplate provided in areas where electrostatic charge can build up.
	Plug connector	The plug connector must not be withdrawn under voltage. The proximity switch is identified as follows: WARNING - DO NOT SEPARATE WHEN ENERGIZED. With the plug connector disconnected, soiling of the internal area must be prevented.(i.e. the area that is inaccessible when the connector is inserted)
General information
Use in the hazardous area		see instruction manuals
	Category	3G 3D

Характеристики

Важная информация

Все информационные материалы, представленные на сайте, носят справочный характер и не могут в полной мере передавать достоверную информацию о свойствах и характеристиках товара.

Фотография на сайте служит дополнительным источником для определения совместимости запчастей с Вашим оборудованием, и не может являться основным. Основной источник по совместимости запчастей - актуальная документация производителя оборудования, из которой значимой информацией для заказа являются: название запчасти и каталожный номер.

Запасные части и комплектующие подбираются самостоятельно покупателем строго по каталожным номерам из официальных деталировок производителей. В случае, если номенклатура товара совпадает с фактически поставленной, но не подходит на оборудование - в ее замене или возврате может быть отказано.

Цены на сайте имеют информационный характер и могут отличаться от цен в коммерческом предложении.